【 Operation Video 】 Operation Instructions For Kailifeng Series High Pressure Cleaning Vehicle

01. Product Overview

Kaili Fengpai Series Road Cleaning Vehicles Are The Latest High-efficiency High-pressure Cleaning Vehicles Developed By Kaili Special Automobile According To The Market Demand. They Not Only Have The Function Of Ordinary Sprinklers, But Also Can High-pressure Clean The Road Surface, Carry Out Spray Dust Reduction, Regulate Air Humidity, Improve Air Quality, And Use High-pressure Water Guns To Clean Road Signs, Billboards, Etc., Suitable For Daily Operations In The Main Streets, Small Streets, Detours And Other Road Sections.

02. Product Features

Independent System Strength Cleaning

It Has Independent High And Low Water System, And The High-pressure System Adopts Imported High-pressure Water Pump, Which Has Good Cleaning Effect And Low Water Consumption. It Cleans The Dirt On The Road Surface With High Pressure And Low Flow Rate, Which Is Efficient And Water-saving. The Low-voltage System Has Functions Such As Road Surface Watering, Cooling, Dust Removal, Cleaning Of Dusty Roofs, Road Maintenance, Garden Watering, And Emergency Firefighting.

Flexible Handling And Strong Adaptability

Electric, Hydraulic And Pneumatic Centralized Control, With Front Spray, Hedge, Rear Spray, Up And Down Spray And Other Modes, The Cab Of Each Cleaning Point Can Be Controlled Separately, Improving The Operation Flexibility And Adaptability To Specific Working Conditions.

Safe And Reliable Operation

Intelligent Operation, The Clear Water Tank Is Equipped With A Low Water Level Alarm Device And A Water Pump Water Shortage Protection Interlock Device To Prevent Damage To The High-pressure Water Pump Due To Water Shortage.

Larger Capacity And Super Strong Capability

Elliptical Water Tank With Anti Wave Plate Installed Inside To Reduce Water Impact. The Maximum Cleaning Pressure Can Reach 13MPa, The Maximum Cleaning Width Can Reach 3.5M, And The Cleaning Water Flow Rate Can Reach 150L/Min.

03. Operating Instructions

1. Pre Homework Inspection

Check Whether The Screws Of Each Fastening Component Are Loose, And Whether There Is Any Leakage Or Air Leakage In The Air Pipe, Water Pipe, And Oil Pipe

2. Pre Job Water Injection Operation Steps

Water Injection Operation Can Be Carried Out Through The Top Water Inlet Of The Tank, The Water Inlet Of The Fire Hose, Or Through The Self-priming Function Of The Low-pressure Pump. During The Water Injection Process, Attention Should Be Paid To The Water Level Of The Tank

3. Front Spray Rack Operation Steps

Start The Chassis Engine, When The Air Pressure Is ≥ 0.8 Megapascals, Turn On The Main Power Switch Of The Control Box, Turn On The Auxiliary Engine Key To The First Gear Position And Start The Auxiliary Engine. After The Auxiliary Engine Is Fully Started, Release The Key Switch. Operate The Cab Box To Control The Front Spray Bracket. The Spray Bracket Can Be Raised, Lowered, Offset Left And Right, And The Left And Right Spray Rods Can Be Extended And Retracted. Select The Appropriate Spray Height, Spray Angle, And Spray Width, And Turn On The Left And Right Spray Switches, Side Spray Switches, And Middle Spray Switch.

Attention: It Can Be Selectively Opened Or Closed Or Fully Opened According To The Road Conditions.

Rotate The Auxiliary Engine Throttle Clockwise To Increase The Auxiliary Engine Speed To 1500 Rpm, Press The Clutch Deeply, Select The Appropriate Low-speed Gear, Slowly Release The Clutch Pedal, Release The Handbrake, And Start Working.

After Completing The Homework, Press The Clutch Deeply, Shift To Neutral, Pull Up The Handbrake, Turn The Throttle Of The Auxiliary Engine Counterclockwise, Lower The Throttle Of The Auxiliary Engine, And Retract The Action Completed By Operating The Front Spray Bracket Before The Homework Through The Cab Control Box

4. Operation Steps Of Rear Spray And Arc Spray Pipe Above The Tank

Open The Rear Spray Changeover Ball Valve And Start The Chassis Engine. When The Air Pressure Is ≥ 0.8 MPa, Turn On The Main Power Switch Of The Control Box. Turn The Auxiliary Engine Key To The First Gear Position And Start The Auxiliary Engine. Release The Key Switch After The Auxiliary Engine Is Fully Started. The Cab Control Box Opens The Rear Spray Switch, And The Auxiliary Engine Throttle Knob Rotates Clockwise To Increase The Auxiliary Engine Speed To 1500 Rpm. Press The Clutch Pedal Deeply, Select The Appropriate Low-speed Gear, Slowly Release The Clutch Pedal, Release The Handbrake, And Start Working. The Rear Spray And The Arc-shaped Spray Pipe Of The Tank Can Be Switched Through The Changeover Ball Valve.

After The Operation Is Completed, Deeply Step On The Clutch, Engage The Neutral Gear, Pull Up The Hand Brake, Rotate The Auxiliary Engine Throttle Knob Counterclockwise, Lower The Auxiliary Engine Throttle, And Close The Rear Spray Switch Through The Cab Operation Box.

5. Operation Steps For Low-pressure Front Flushing, Rear Showerhead, And Rear Anti-aircraft Gun

Start The Chassis Engine, When The Air Pressure Is ≥ 0.8 Megapascals, Turn On The Main Power Switch Of The Control Box, Turn On The Auxiliary Engine Key To The First Gear Position And Start The Auxiliary Engine. After The Auxiliary Engine Is Fully Started, Release The Key Switch. Open The Left Front Punch And Right Front Punch Switches In The Cab Control Box

Press The Clutch Pedal Deeply, Turn On The Power Take-off Switch, Select The Appropriate Low-speed Gear, Slowly Release The Clutch Pedal, Release The Handbrake, And Start Working

After Completing The Homework, Press The Clutch Deeply, Load The Gear Lever Into Neutral Position, Turn Off The Power Take-off Switch, And Turn Off The Left And Right Front Thrust Switches.

(The Operation Steps For The Rear Showerhead And Rear Anti-aircraft Gun Are The Same As Above)